Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
In this article down the page you can locate a lot of helpful advice when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't exactly rocket science, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily obtainable, the project can relocate rapidly; if you need to open a wall surface to remove the old bathtub and place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Ensure you have actually qualified yourself for the work as well as fit attempting it. As opposed to working with a specialist to take over a halfway-completed job, it is better to think about using one before you start. Chances are you may require a professional plumber to make tube links.
This article will aid you mount a new tub in your bathroom if you have currently acquired a new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your devices and also material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be quite problematic because of the restricted gain access to that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Using both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the tub up until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water supply as well as inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait till the tub has actually been used at the very least once as this will certainly settle it right into its final placement.
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom and the tiling, resulting in issues with moisture as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes and also cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before sealing, to enable the movement experienced when the tub is in use. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very excited about How to Install a Bathtub and I hope you enjoyed reading the entry. Kindly take a moment to distribute this article if you liked it. Thanks for your time. Please check up our website back soon.
Book Your Installation Report this page